TIP 0304-73 "Checking for coating wear on corrugating rolls" (Revision)

TIP 0305-02 "Maintenance on computer-assisted machinery" (Revision)

TIP 0305-12 "Installation" (Revision)

TIP 0305-18 "Proper use of pull bands" (Revision)

UM 251 "Permanganate number of pulp" (formerly withdrawn UM revised and returned to set)

Special note:  Documents appearing in the TAPPI online version of the Standards and TIPs are updated once a month (usually around the 15th). So it is possible that there is a delay between the publication announcement and the posting online. If you are a subscriber to the online access to Standards and TIPs and you are in a hurry for new documents that have not yet been posted, you can send a request to standards@tappi.org.

 

The TAPPI Standards regulations require public review of standards that are up for ballot. TAPPI members can view any drafts that are in ballot by logging in to the TAPPI web site (www.tappi.org), clicking on "My TAPPI," and then clicking on the "Standards Public Draft Review" link on the left side of the page. If you would like to review and comment on any draft and are not a member of the corresponding Standard-Specific Interest Group (SSIG), you may view the draft on line or you may request a copy of the draft being balloted by writing to standards@tappi.org. TAPPI members may join SSIGs as permanent members; go to the Subject Category page to download forms for this purpose. Nonmembers of TAPPI may join any SSIG as a voting member; to do so, send a message to standards@tappi.org to receive a copy of the draft and a ballot.

Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting.

T 824 om-09 "Fluted edge crush of corrugating medium (flexible beam method)" (November 4, 2013)

T 631 om-09 "Microbiological enumeration of process water and slush pulp" (November 7, 2013)

T 534 "Brightness of clay and other mineral pigments (d/0 diffuse)" (November 8, 2013)

T 515 "Visual grading and color matching of paper" (November 15, 2013)

T 257 "Sampling and preparing wood for analysis" (November 15, 2013)

T 480 "Specular gloss of paper and paperboard at 75 degrees" (November 22, 2013)

T 458 "Surface wettability of paper (angle of contact method)" (December 2, 2013)

Special note about the online balloting system: TAPPI has been experiencing some problems on its website with the online system for balloting. The problem may or may not have been corrected by the time of the publication fo this edition of the STAR newsletter.

If you are a TAPPI member and expderience problems trying to access drafts and vote on line, send a message to standards@tappi.org and request that a copy of the draft be sent to you. then you can vote by replying to the email. We apologize for the inconvenience.

 

 

Getting started is easy. Do you have just a general idea for a standard, or are you farther along and have a substantial draft? If you just have a general idea for a standard or TIP, complete the New Idea Submission Form. TAPPI will review your idea and identify an appropriate committee or group to work on your suggestion. If you are further along, send an initial draft to standards@tappi.org. From there, the TAPPI Standards Manager will guide you through the appropriate process to finalize and approve the new document.

 

A new TIP, "Recovery Boiler Leak Indication," has been proposed. The scope is:

"The purpose of this technical information paper is to itemize the boiler operating parameters that may provide information about a pressure part leak in the recovery boiler.  Each item will be accompanied by an explanation of how and why these parameters indicate a leak."

If you would like more information or if you would like to participate in the development of this TIP, please contact standards@tappi.org by November 15, 2013.

 

TIP 0305-31 "Daily and month-to-date status report" has been withdrawn based on a recommendation of the Working Group reviewing the TIP.

As announced in the August 2013 issue of STAR. The working group believes that it is no longer necessary due to the number of computer driven maintenance programs currently available.

Withdrawn TIPs are still availbale for TAPPI members free of charge, or for nonmembers at a price of $10.

 

A ballot on T 526 cm-04 "Blister resistance of coated paper in heatset printing" was distributed for its ten-year review ballot on May 7, 2013. Due to low response to the ballot, a second ballot was distributed on July 17, 2013. The percent return of this ballot was also low.

Under the current TAPPI guidelines, this method was balloted for withdrawal in this review because it is a Classical Method that has been through regular review more than once. There was one negative voting against withdrawal, and that voter has agreed to become working group chair for the review and has requested that the next ballot be for retention and possibly revision of T 526 as a Classical Method.

Because of the low percent return, several members of the Standard-Specific Interest Group (SSIG) are in danger of being dropped after the next ballot due to missing three ballots in a row. However, if all of those members are dropped, then we will drop below the minimum 10 members required to constitute an SSIG.

In order to have enough SSIG members after the delinquent members are dropped, we need to add new members to the SSIG. If you have an interest in T 526 and would like to join this SSIG, please send a message to standards@tappi.org no later than November 15, 2013.

 

The next meeting of the Standards Advisory Review Group (SARG) is scheduled for Tuesday, November 5, 2013, 1:30 pm EASTERN time, at TAPPI Headquarters.  SARG approval is the last step prior to publication for any new or revised standard.

In order to act on any appeals from TAPPI members relevant to the standards up for approval, the SARG meeting is open to anyone for participation. The agenda has been posted on the TAPPI SARG page and is shown below. If you would like to participate in the SARG meeting by conference call, please send a message before November 5, 2013, to standards@tappi.org.

AGENDA

Standards Advisory Review Group
Tuesday, November 5, 2013
1:30 pm (EASTERN time)
TAPPI Headquarters
Atlanta, GA

I. Welcome and introductions
II. Antitrust Statement
III. Approval of Agenda
IV. Approval of Minutes from April 30, 2013
V. Standards ready for final approval (* indicates standards eligible for submission as American National Standards)

1. *T 494 "Tensile properties of paper and paperboard (using constant rate of elongation apparatus)"
2. *T 511 "Folding endurance of paper (MIT tester)"
3. T 210 "Sampling and testing wood pulp shipments for moisture"
4. *T 236 "Kappa number of pulp"
5. *T 459 "Surface strength of paper (wax pick test)"
6. *T 812 "Ply separation of solid and corrugated fiberboard (wet)"
7. *T 524 "Color of paper and paperboard (45/0, C/2)"
8. *T 527 "Color of paper and paperboard (d/0, C/2)"
9. *T 836 "Bending stiffness, four point method"
10. *T 808 "Flat crush test of corrugated board (flexible beam method)"
11. T 577 "Score bend test"

VI. Other business
VII. Next meeting
VIII. Adjournment

 

Reports outlining the overdue reviews for Standards and TIPs were sent to the Quality and Standards Management Committee (Q&SMC) on August 19, 2013. Copies of these reports were also sent to the assigned Working Group Chairmen for these overdue reviews as well as to chairmen of the appropriate technical groups in TAPPI.

Anyone who did not receive the overdue reports but who have an interest may obtain copies by requesting them from standards@tappi.org.

Working Group Chairmen: These reports were sent to you for your information and action, if required. Q&SMC may, according to the Standards Guidelines, withdraw any Standards or TIPs whose reviews are overdue, especially if it appears that little progress is being made on the Work Item. If more information or indications of progress on these Work Items are received prior to the next meeting (November 5, 2013), Q&SMC will take these reports of progress under consideration. 

To provide updates regarding these reports, send a message to to standards@tappi.org no later than Monday, November 4, 2013, in order to be able to provide this information to Q&SMC at their next meeting.

 

For details on these commonly-used acronyms in the development of TAPPI Standards and TIPs, please see the Standards Guidelines and the TIP Guidelines, or send your questions to standards@tappi.org.

TIP = Technical Information Paper
Q&SMC = Quality and Standards Management Committee
SSIG = Standard-Specific Interest Group
SARG = Standards Advisory Review Group
WI = Work Item
WG = Working Group
WGC = Working Group Chairman
om = Official Method
pm = Provisional Method
sp = Standard Practice
cm = Classical Method
ss = Standard Specification
sg = Standard Guideline
gl = Standard Glossary
wd = Withdrawn Standard
UM = Useful Method

 

Details on how to search and order TAPPI Standards, TIPs and Useful Methods can be found on the TAPPI website's Search and Order page.

For Individual TIPs, order Item Number: 0108____ (Insert TIP number)

For Individual Standards, order Item Number: 0104T____ (Insert Standard number)

For individual Useful Methods, order Item Number 0104UM____ (insert UM number)

List price: $49; TAPPI member price: $32. There are no shipping or handling charges for electronic documents.

The 2013 collection of Standards, TIPs, and UMs, published in March of 2013 (product code STUCD-13), is available on CD. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available.

For information and quotes on company licenses, contact Jeff Wellsat jwells@tappi.org or +1-770-209-7228. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order on line at www.tappi.org.