TIP 0402-11 "Liquid penetrant testing of new suction roll shells" (Revision)

TIP 0404-25 "Guidelines for the design, operation, performance evaluation, and troubleshooting of a paper machine hood and air systems" (Revision, including title change)

Special note:  Documents appearing in the TAPPI online version of the Standards and TIPs are updated once a month (usually around the 15th). So it is possible that there is a delay between the publication announcement and the posting online. If you are a subscriber to the online access to Standards and TIPs and you are in a hurry for new documents that have not yet been posted, you can send a request to standards@tappi.org.

 

The TAPPI Standards regulations require public review of standards that are up for ballot. Send a message to standards@tappi.org if you want to request a copy of draft in ballot.

Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting.

T 1014 "Moisture sensitivity of fiber glass mats" (October 3, 2014)

T 259 "Species identification of nonwood plant fibers" (October 10, 2014)

T 200 "Laboratory beating of pulp (Valley beater method)" (October 17, 2014)

T 401 "Fiber analysis of paper and paperboard" (October 17, 2014)

T 829 "Score quality test" (October 20, 2014)

T 1007 "Sample location for fiber glass mat sheets" (October 23, 2014)

T 562 "CIE whiteness and tint of paper and paperboard (45/0 geometry, C/2 illuminant/observer)" (October 24, 2014)

CORRECTION:
Last month, T 840 was listed as being balloted for withdrawal. However, the wrong title was listed for T 840. T 840 is "Testing adhesives used in glued lap joints of corrugated fiberboard containers." It is in ballot for withdrawal, and the ballot is due September 26, 2014.

 

EcoLogo Certifications are voluntary, multi-attribute, lifecycle based environmental certifications that indicate a product has undergone rigorous scientific testing, exhaustive auditing, or both, to prove its compliance with stringent, third-party, environmental performance standards. Underwriters Laboratories (UL) provides third-party certifications based on its ECOLOG Standards

EcoLogo has reviewed the comments that were received on Draft 2 of a proposed revision to the Standard for Sustainability of Disposable Wipers (formerly CCD-173).  Note that UL will be issuing a new standard number prior to publication.

Comments from Draft 1 have been reviewed, and the next draft has been issued. EcoLogo is launching another round of public consultation on the Disposable Wipers Standard (Draft 2) and are requesting additional comments and input.

The public review comment period will close October 3, 2014. If your company would like to review the draft and submit comments, please contact standards@tappi.org, and the package of materials will be sent to you.

 

Getting started is easy. Do you have just a general idea for a standard, or are you farther along and have a substantial draft? If you just have a general idea for a standard or TIP, complete the New Idea Submission Form. TAPPI will review your idea and identify an appropriate committee or group to work on your suggestion. If you are further along, send an initial draft to standards@tappi.org. From there, the TAPPI Standards Manager will guide you through the appropriate process to finalize and approve the new document.

 

Plans are already underway for the 100th Anniversary of TAPPI, which will be observed during the 2015 PaperCon Conference in Atlanta, April 19-22.2015.

As part of the celebration, TAPPI and the American National Standards Institute (ANSI) have invited ISO Technical Committee TC 6 and its subcommittees and working groups to hold its 2015 meeting during the PaperCon week.

To keep up with the 100th Anniversary plans, there's a special website: http://www.tappi100years.org. On this site you can also sign up for the special newsletter for this event.

 

The five-year review ballot for T 553 "Alkalinity of paper as calcium carbonate (alkaline reserve of paper) went out in July and was due on September 5, 2014. At the time of the ballot, there were 10 members on the Standard-Specific Interest Group (SSIG), which is the minimum required to validate the SSIG.

When the ballot was tabulated, one member was dropped for missing three consecutive ballots in a row, which means that now we are short at least one member on the SSIG. A ballot cannot be validated until we have the required number on the SSIG.

If you would like to join this SSIG, please send a message to standards@tappi.org no later than October 15, 2014.

 

The standards eligible for approval at SARG are listed below. The asterisks (*) indicate the standards that will be eligible for submission to ANSI for consideration as American National Standards.

*T 835 "Water absorption of corrugating medium: water drop absorption test"

*T 449 "Bacteriological examination of paper and paperboard"

T 458 "Surface wettability of paper (angle of contact method)"

*T 845 (NEW Standard - WI 3031) "Wet pin adhesion of corrugated board by selective separation"

*T 702 "Rheological measurements for characterization of polyolefins: low-density polyethylene (LDPE) for extrusion coating"

 

 

The next meeting of the Standards Advisory Review Group (SARG) is scheduled by conference call on Tuesday, November 4, at 1:30 pm Eastern time.  SARG approval is the last step prior to publication for any new or revised standard.

In order to act on any appeals from TAPPI members relevant to the standards up for approval, the SARG meeting is open to anyone for participation. The agenda will be posted on the SARG page at least 50 days prior to the meeting, in accordance with TAPPI’s guidelines. There will be links from the agenda items to the final drafts that are up for approval.

If you would like to participate in the SARG meeting by conference call, please send a message before November 4, 2014, to standards@tappi.org.

 

 

Reports outlining the overdue reviews for Standards and TIPs were sent to the Quality and Standards Management Committee (Q&SMC) on August 5, 2014. Copies of these reports were also sent to the assigned Working Group Chairmen for these overdue reviews as well as to chairmen of the appropriate technical groups in TAPPI.

Anyone who did not receive the overdue reports but who have an interest may obtain copies by requesting them from standards@tappi.org.

Working Group Chairmen: These reports were sent to you for your information and action, if required. Q&SMC may, according to the Standards Guidelines, withdraw any Standards or TIPs whose reviews are overdue, especially if it appears that little progress is being made on the Work Item. If more information or indications of progress on these Work Items are received prior to the next meeting (November 4, 2014), Q&SMC will take these reports of progress under consideration. 

To provide updates regarding these reports, send a message to standards@tappi.org no later than Monday, November 3, 2014, in order to be able to provide this information to Q&SMC at their next meeting.

 

For details on these commonly-used acronyms in the development of TAPPI Standards and TIPs, please see the Standards Guidelines and the TIP Guidelines, or send your questions to standards@tappi.org.

TIP = Technical Information Paper
Q&SMC = Quality and Standards Management Committee
SSIG = Standard-Specific Interest Group
SARG = Standards Advisory Review Group
WI = Work Item
WG = Working Group
WGC = Working Group Chairman
om = Official Method
pm = Provisional Method
sp = Standard Practice
cm = Classical Method
ss = Standard Specification
sg = Standard Guideline
gl = Standard Glossary
wd = Withdrawn Standard
UM = Useful Method

 

Details on how to search and order TAPPI Standards, TIPs and Useful Methods can be found on the TAPPI website's Search and Order page.

For Individual TIPs, order Item Number: 0108____ (Insert TIP number)

For Individual Standards, order Item Number: 0104T____ (Insert Standard number)

For individual Useful Methods, order Item Number 0104UM____ (insert UM number)

List price: $49; TAPPI member price: $32. There are no shipping or handling charges for electronic documents.

 

The 2014 collection of Standards, TIPs, and UMs, published in March of 2014 (product code STUCD-14), is available on CD. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available.

For information and quotes on company licenses, contact Ashley Westbrook (awestbrook@tappi.org) or +1-770-209-7228. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order on line at www.tappi.org.

 

TAPPI Standards, TIPs and Useful Methods Online Subscription gives you point-and-click access, providing immediate answers anytime problems arise.

You’ll save $186 alone by purchasing a subscription to Standards, TIPs and Useful Methods Online along with a TAPPI membership.  This offer also applies each year you renew your membership.

By joining TAPPI, you receive substantial savings on all TAPPI events, products and services and receive Paper 360, TAPPI Journal and Specialty Newsletters.

Combine the Power of TAPPI Membership and the Quality of Performance by purchasing a TAPPI membership along with Standards online.  Be a part of the TAPPI Community.

TAPPI Membership $174 + Standards Online $125 = $299
Non-members Standards Online = $485

TAPPI Standards, TIPs and Useful Methods – on demand – anytime, anywhere.