| Archive | Subscribe | Printer-Friendly Version | Advertise | tappi.org | TAPPI Press Catalog | February 2021 |
|
TAPPI Standards in Ballot
Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting. T 237 cm-08 Carboxyl content of pulp (3/29/2021) T 249 cm-09 Carbohydrate composition of extractive-free wood and wood pulp by gas-liquid chromatography (3/29/2021) T 631 om-16 Microbiological enumeration of process water and slush pulp (3/07/2021) The TAPPI Standards regulations require public review of standards that are up for ballot. Send a message to standards@tappi.org if you want to request a copy of the draft in ballot. If you would like to participate in the SSIGs that review and vote on the Standards, please contact TAPPI Standards Department at standards@tappi.org. General Announcements
The TAPPI CD of Standards, TIPs, and UMs has been discontinued for 2021 The TAPPI CD of Standards, TIPs, and UMs has been discontinued for 2021. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available. All individual: TIPs or Standards are available for electronic or paper delivery. For electronic delivery, the documents are downloaded in PDF format. Hard copy documents can be mailed or faxed, but shipping and handling costs will apply. Propose a New Standard or Technical Information Paper (TIP) Getting started is easy. Do you have just a general idea for a Standard, or are you farther along and have a substantial draft? If you just have a general idea for a Standard or TIP, complete the New Idea Submission Form. TAPPI will review your idea and identify an appropriate committee or group to work on your suggestion. If you are further along, send an initial draft to standards@tappi.org. From there, the TAPPI Standards Manager will guide you through the appropriate process to finalize and approve the new document. STAR of the Month
 “I found it very impactful learning that there’s more to Standards than the technicalities of Standards.” – Dr. Tony Lyons A Multidimensional Leader Dedicated to the Industry! Dr. Lyons has more than 36 years of experience in the areas of paper coating, paper finishing, and mineral pigments for paper coating, paper filling and other specialty applications. He received his Doctorate in Chemical Engineering from Lehigh University. He also holds Bachelor and Master of Science degrees in Chemical Engineering from the State University on New York at Buffalo. His work experiences include time with Westvaco and Repap Technologies, Inc. He retired in 2017 from IMERYS after 25 years and established Paper Lyons LLC for the purpose of doing science and technology consulting. Tony is an adjunct professor at University of Maine and Western Michigan University. He has been an active member of TAPPI since 1985 and has volunteered for various leadership roles, including being elected to and serving on the Board of Directors. He holds patents in coating pigments, coating applications, coated inkjet papers, agricultural applications and barrier coating.
Read More... SSIG Members Needed
The Standard-Specific Interest Groups (SSIGs) for the following Standards are in need of additional members. These groups may or may not have ballots currently open. All Standard-Specific Interest Groups (SSIG) require a minimum of 10 members in order to ballot and vote on a draft of a method. The following test methods do not have the required minimum number of members to initiate a ballot:
Alkaline Pulping Chemical Properties T 244 cm-11 Acid-insoluble ash in wood, pulp, paper, and paperboard T 252 om-16 pH and electrical conductivity of hot water extracts of pulp, paper, and paperboard T 429 cm-10 Alpha-cellulose in paper T 434 cm-10 Acid-soluble iron in paper T 435 om-16 Hydrogen ion concentration (pH) of paper extracts (hot extraction method) T 493 cm-10 Identification and determination of melamine resin in paper T 509 om-15 Hydrogen ion concentration (pH) of paper extracts (cold extraction method) T 600 om-15 Analysis of formaldehyde in aqueous solutions and of free formaldehyde in resins T 610 sp-15 Preparation of indicators and standard solutions T 613 cm-10 Analysis of caustic soda T 617 cm-10 Analysis of lime T 618 cm-10 Analysis of limestone T 619 cm-10 Analysis of salt cake T 621 cm-10 Analysis of rosin T 622 cm-10 Analysis of sodium hydrosulfite T 624 cm-11 Analysis of soda and sulfate white and green liquors T 628 cm-10 Analysis of rosin size T 632 cm-11 Analysis of sodium silicate Fillers and Pigments Optical Properties T 1214 sp-17 Interrelation of reflectance, R0; reflectivity, R ; TAPPI opacity, C0.89; scattering, s; and absorption, k T 1219 sp-17 Storage of paper samples for optical measurements and color matching Physical Properties T 578 sp-16 Accelerated light aging of printing and writing paper by xenon-arc exposure apparatus Pulp Properties
Building and Industrial Material Participating in a SSIG is free and open to anyone interested. Join now! If no progress is made on balancing these SSIGs, then the respective methods may be considered for withdrawal at the next Q&SMC meeting. If you have an interest in becoming a member of either of these SSIGs please contact standards@tappi.org. or visit tappi.org/JoinStandards. Standards Coming Up For Review
The system for review and development of TAPPI Standards requires an announcement of review dates so that any interested TAPPI parties may access the drafts, submit comments, and/or join the Standard-Specific Interest Group (SSIG) to cast an official vote. The list of Standards up for review in 2021 has been corrected to remove two Standards that were incorrectly classified as up for review in October 2021. These Classical Methods have a 10 year review timeframe so will not be up for review until 2026. T 204 cm-17 Solvent extractives of wood and pulp T 418 cm-17 Organic nitrogen in paper and paperboard The below 24 Standards will be up for review in 2021. The date indicated is the target date on which the draft will be distributed to the Standard-Specific Interest Group (SSIG) for that particular Standard. Any interested individuals who wish to be part of the voting for any Standard should contact the Standards Department at TAPPI (standards@tappi.org), phone +1-770-209-7249 or fax +1-770-446-6947) and request voting membership on the corresponding SSIG, prior to the target ballot date. You may also visit tappi.org/JoinStandards and complete the short form to get started. If you join the Standard Specific Interest Group for any Standard, you will receive a notice for ballot at the proper time with instructions for casting your vote and making your comments. T 559 cm-12 Grease resistance test for paper and paperboard - April 21 T 400 sp-17 Sampling and accepting a single lot of paper, paperboard, containerboard, or related product - April 21 T 278 sp-17 Pulp screening (Valley-type screening device) - April 21 T 227 om-17 Freeness of pulp (Canadian standard method) - April 21 T 433 cm-12 Water resistance of sized paper and paperboard (dry indicator method) - April 21 T 448 om-17 Water vapor transmission rate of paper and paperboard at 23 degrees C and 50% RH - April 21 T 581 om-17 Dry tensile properties of paper towel and tissue products (using constant rate of elongation apparatus) - April 21 T 413 om-17 Ash in wood, pulp, paper and paperboard: combustion at 900 degrees C - April 21 T 838 cm-12 Edge crush test using neckdown - April 21 T 821 om-17 Pin adhesion of corrugated board by selective separation - April 21 T 827 om-17 Box blank dimensioning - April 21 T 809 om-17 Flat crush of corrugating medium (CMT test) April 21 T 811 om-17 Edgewise compressive strength of corrugated fiberboard (short column test) - April 21 T 810 om-17 Bursting strength of corrugated board - April 21 T 802 om-17 Drop test for fiberboard shipping containers - April 21 T 519 om-17 Diffuse opacity of paper (d/0 paper backing) - April 21 T 832 om-17 Water absorption of corrugating medium: float curl method - October 21 T 525 om-17 Diffuse brightness of paper, paperboard and pulp (d/0) – ultraviolet level C - October 21 T 1214 sp-17 Interrelation of reflectance, R0; reflectivity, R ; TAPPI opacity, C0.89; scattering, s; and absorption, k - October 21 T 1219 sp-17 Storage of paper samples for optical measurements and color matching - October 21 T 234 cm-12 Coarseness of pulp fibers - November 21 T 483 cm-12 Odor of packaging materials - November 21 T 697 cm-12 Accelerated test for viscosity stability of clay slurries - November 21 T 665 cm-12 Analysis of talc - November 21 U.S. TAG to ISO TC 6
The ISO TC6 meetings originally scheduled for June in Beijing will take place virtually. Here is the general schedule: May 25 & 26, 2021 – ISO/TC6/SC2 Plenary meeting (2-4 hours per day) – only registered Experts and the Head of Delegation for each member country may attend All Working Groups associated with TC6 are going to hold their meetings in advance so status reports and proposed resolutions will be available at least 6 prior to the Plenary meetings weeks (beginning of April). Only registered Experts of each member country may attend.
Contact Todd Popson, Chair of US TAG to ISO TC6 to learn more about becoming an Expert on any ISO TC6 activities. Todd Popson Did You Know
... that to participate in the balloting process for TAPPI Standards you must sign up for the Standard-Specific Interest Groups (SSIGs)? Drafts are available for anyone... that to participate in the balloting process for TAPPI Standards you must sign up for the Standard-Specific Interest Groups (SSIGs)? Drafts are available for anyone to review, but to vote and comment you must be a member of the SSIG. Each Standard has its own SSIG – so you have to sign up for each Standard that you have an interest in. Links to all of the SSIGs (by subject category) can be found on the Subject Category for Standards web page. Visit tappi.org/JoinStandards to join now. Acronyms You May Need to Know
TIP = Technical Information Paper Q&SMC = Quality and Standards Management Committee SSIG = Standard-Specific Interest Group SARG = Standards Advisory Review Group WI = Work Item WG = Working Group WGC = Working Group Chair om = Official Method pm = Provisional Method sp = Standard Practice cm = Classical Method ss = Standard Specification sg = Standard Guideline gl = Standard Glossary wd = Withdrawn Standard UM = Useful Method Searching and Ordering TAPPI Standards, TIPs, and Useful Methods
Details on how to search and order TAPPI Standards, TIPs, and Useful Methods can be found on the TAPPI website’s Search and Order page. All individual TIPs or Standards are available for electronic or paper delivery. For electronic delivery, the documents are e-mailed in PDF format. Hard copy documents can be mailed or faxed, but shipping and handling costs will apply. For Individual TIPs, order Item Number: 0108____ (Insert TIP number) For Individual Standards, order Item Number: 0104T____ (Insert Standard number) For individual Useful Methods, order item number: 0104UM_____ (Insert UM number) List price: $49; TAPPI member price: $32. There are no shipping or handling charges for electronic documents. The TAPPI CD of Standards, TIPs, and UMs has been discontinued for 2021. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available. For information and quotes on company licenses, contact TAPPI Press (press@tappi.org) or +1-770-209-7277. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order on line at www.tappi.org. ----------------------------------------------------------------------------------------------- Search and Order Individual Access or Company license Join a SSIG Develop a TIP Standards Guidelines TIPs Guidelines |
|
TAPPI Standards guidelines require that all TAPPI members receive notification of any proposed new Standards or TIPs. This message is being sent to you because of your affiliation with TAPPI; have purchased TIPs or Standards products from TAPPI; or because you have previously expressed interest in this topic.
TAPPI is the leading technical association for the worldwide pulp, paper and converting industry.
15 Technology Parkway South | Suite 115 | Peachtree Corners, GA 30092 | www.tappi.org
1-800-332-8686 (US) | 1-800-446-9431 (Canada) | +1-770-446-1400 (Worldwide)
TAPPI Privacy Policy
