| Archive | Subscribe | Printer-Friendly Version | Advertise | tappi.org | TAPPI Press Catalog | November 2022 |
The Year Wraps with Great Strides from TAPPI's Standards
31 TAPPI Standards Approved as American National Standards!
Don't miss the chance to vote on Standard reviews.
Click here to join any Standard-Specific Interest Group (SSIG)
|
New or Revised Standards, TIPs, and Useful Methods
Check here the list of TAPPI Technical Information Papers (TIPs) recently published: T 1006 sp-22 Testing of fiber glass mats: use of modified TAPPI procedures for sampling and lot acceptance, stiffness, tear resistance, and thickness (Reaffirmed) T 1007 sp-22 Sample location for fiber glass mat sheets (Reaffirmed) T 1013 om-22 Loss on ignition of fiber glass mats (Reaffirmed) T 1210 sp-22 Units of measurement and conversion factors (Reaffirmed) T 1214 sp-22 Interrelation of reflectance, R0; reflectivity, R ; TAPPI opacity, C0.89; scattering, s; and absorption, k (Reaffirmed) T 1216 sp-22 Indices for whiteness, yellowness, brightness, and luminous reflectance factor (Reaffirmed) T 1219 sp-22 Storage of paper samples for optical measurements and color matching (New) T 207 cm-22 Water solubility of wood and pulp (Reaffirmed) T 212 om-22 One percent sodium hydroxide solubility of wood and pulp (Reaffirmed) T 236 om-22 Kappa number of pulp (Revised) T 254 cm-22 Cupriethylenediamine disperse viscosity of pulp (falling ball method) (Reaffirmed) T 262 sp-22 Preparation of mechanical pulps for testing (Reaffirmed) T 265 cm-22 Natural dirt in wood chips (Reaffirmed) T 274 sp-22 Laboratory screening of pulp (MasterScreen-type instrument) (Revised) T 281 sp-22 Open drum washer mat sampling technique (Reaffirmed) T 403 om-22 Bursting strength of paper (Revision) T 413 om-22 Ash in wood, pulp, paper and paperboard: combustion at 900°C (New) T 419 om-22 Starch in paper (Reaffirmed) T 421 cm-22 Qualitative (including optical microscopic) analysis of mineral filler and mineral coating of paper (Reaffirmed) T 431 cm-22 Ink absorbency of blotting paper (Reaffirmed) T 449 om-22 Bacteriological examination of paper and paperboard (Revision) T 464 om-22 Water vapor transmission rate of paper and paperboard at high temperature and humidity (Reaffirmed) T 519 om-22 Diffuse opacity of paper (d/0 paper backing) (Reaffirmed) T 525 om-22 Diffuse brightness of paper, paperboard and pulp (d/0) -- ultraviolet level C (Reaffirmed) T 534 om-22 Brightness of clay and other mineral pigments (d/0 diffuse) (New) T 536 om-22 Resistance of paper to passage of air (high-pressure Gurley method)(Reaffirmed) T 559 cm-22 Grease resistance test for paper and paperboard (Reaffirmed) T 578 sp-22 Accelerated light aging of printing and writing paper by xenon-arc exposure apparatus (New) T 581 om-22 Dry tensile properties of paper towel and tissue products (using constant rate of elongation apparatus) (New) T 600 om-22 Analysis of formaldehyde in aqueous solutions and of free formaldehyde in resins (New) T 604 cm-22 Sulfur dioxide in sulfite cooking liquor (Reaffirmed) T 653 om-22 Specular gloss of paper and paperboard at 20 degrees (new) T 802 om-22 Drop test for fiberboard shipping containers (new) T 809 om-22 Flat crush of corrugating medium (CMT test) (new) T 810 om-22 Bursting strength of corrugated board (new) T 821 om-22 Pin adhesion of corrugated board by selective separation (Reaffirmed) T 822 om-22 Ring crush of paperboard (rigid support method) (new) T 832 om-22 Water absorption of corrugating medium: float curl method (Revision) Special thanks to the SSIG members below for being the Working Group Chairs in the recently published reviews of TAPPI Standards: Jeff Lundeen WGC for: Walter Rantanen WGC for: Bogdan Marian Tofanica WGC for: Alejandra Jurado WGC for: M. Todd Popson WGC for: Chris Czyryca WGC for: Wilco de Groot WGC for: Todd Bolton WGC for: Dave Carlson WGC for: David Loebker WGC for: Dan Hollingshead WGC for: Matt Przysiecki WGC for: Gregg Reed WGC for: Ben Frank WGC for: The TAPPI Standards Department would also like to express its gratitude to all volunteers who participated in the review of those Standards as SSIG members. 31 TAPPI Standards approved as American National Standards The following TAPPI Standards have been approved as American National Standards by the ANSI Board of Standards Review: ***When new ANS are approved. New American National Standards: *T 413 om-22 Ash in wood, pulp, paper and paperboard combustion at 900°C *T 519 om-22 Diffuse opacity of paper (d/0 paper backing) *T 525 om-22 Diffuse brightness of paper, paperboard and pulp (d/0) – ultraviolet level C *T 534 om-22 Brightness of clay and other mineral pigments (d/0 diffuse) *T 578 sp-22 Accelerated light aging of printing and writing paper by xenon-arc exposure *T 581 om-22 Dry tensile properties of paper towel and tissue products (using constant rate of elongation apparatus) *T 600 om-22 Analysis of formaldehyde in aqueous solutions and free formaldehyde in resins *T 653 om-22 Specular gloss of paper and paperboard at 20 degrees *T 802 om-22 Drop test for fiberboard shipping containers *T 809 om-22 Flat crush of corrugating medium (CMT test) *T 810 om-22 Bursting strength of corrugated board *T 822 om-22 Ring crush of paperboard (rigid support method) *T 1214 sp-22 Interrelation of reflectance, R0; reflectivity, R ; TAPPI opacity, C0.89; scattering, s; and absorption, k *T 1219 sp-22 Storage of paper samples for optical measurements and color matching Approved reaffirmation of current American National Standards: *T 212 om-22 One percent sodium hydroxide solubility of wood and pulp *T 262 sp-22 Preparation of mechanical pulps for testing *T 281 sp-22 Open drum washer mat sampling technique *T 419 om-22 Starch in Paper *T 464 om-22 Water vapor transmission rate of paper and paperboard at high temperature and humidity *T 536 om-22 Resistance of paper to passage of air (high-pressure Gurley method) *T 821 om-22 Pin adhesion of corrugated board by selective separation *T 1006 sp-22 Testing of fiber glass mats: use of modified TAPPI procedures for sampling and lot acceptance, stiffness, tear resistance, and thickness *T 1007 sp-22 Sample location for fiber glass mat sheets *T 1013 om-22 Loss on ignition of fiber glass mats *T 1210 sp-22 Units of measurement and conversion factors *T 1216 sp-22 Indices for whiteness, yellowness, brightness, and luminous reflectance factor Approved revision of current American National Standards: *T 236 om-22 Kappa number of pulp *T 274 sp-22 Laboratory screening of pulp (Master Screen-type instrument) *T 403 om-22 Burst strength of paper *T 449 om-22 Bacteriological examination of paper and paperboard *T 832 om-22 Water absorption of corrugating medium: float curl method Notices of the approvals of the TAPPI Standards as American National Standards were placed in the November 4th, 2022, November 11th, 2022, and November 18th, 2022 edition of ANSI Standards Action. Check here the list of TAPPI Technical Information Papers (TIPs) recently published: TIP 0425-05 Guidelines for Usage of MAP on Raw Yankee Surfaces, WGC: Jeffrey Peters TIP 0606-30 Chlorine dioxide (ClO2) safe storage and handling, WGC: Peter W. Hart Special note: Documents appearing in the TAPPI online version of the Standards and TIPs are updated once a month (usually around the 30th). So it is possible that there is a delay between the publication announcement and the posting online. If you are a subscriber to the online access to Standards and TIPs and you are in a hurry for new documents that have not yet been posted, you can send a request for TIPs to tip@tappi.org or for Standards to standards@tappi.org. TAPPI Standards in Ballot
Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting.
The TAPPI Standards regulations require public review of standards that are up for ballot. Send a message to standards@tappi.org if you want to request a copy of the draft in ballot. If you would like to participate on any SSIGs to review and vote on Standards, please click here or contact standards@tappi.org. TIPs under review
Listed below are TAPPI TIPs that were recently submitted to the Working Group for review. The date when the Work Item was opened is shown for each TIP, as well as the Subject Category under which the TIP is assigned and the Working Group Chair's (WGC) name. The target completion date for the review of each TIP is one year after the opening of the Work Item. 0305 Production
If you would like to participate in the Working Group to review any of these TIPs, please write to tip@tappi.org General Announcements
Slate Announced for Election of 2023 TAPPI Board of Director The candidates are:
More information about these candidates and election process is available on the TAPPI website. Elections will begin December 15, 2022 and conclude January 31, 2023. Contact Mary Beth Cornell, + 1 770-209-7210 or mcornell@tappi.org with questions.
STAR of the Month
ANSI/TAPPI T 212 om-22: One percent sodium hydroxide solubility of wood and pulp Scope Significance Purchasing link: https://imisrise.tappi.org/TAPPI/Products/01/T/0104T212.aspx
Do you have an idea for a NEW TAPPI Standard or Technical Information Paper? We want to hear about it! Please fill out and submit the New Idea Submission form. SSIG Members Needed
The Standard-Specific Interest Groups (SSIGs) for the following Standards are in need of additional members. These groups may or may not have ballots currently open. All Standard-Specific Interest Groups (SSIG) require a minimum of 10 members in order to ballot and vote on a draft of a method. The following test methods do not have the required minimum number of members to initiate a ballot: T 425 om-21 Opacity of paper (15/d geometry, illuminant A/2 degrees, 89% reflectance backing and paper backing)
T 515 om-20 Visual grading and color matching of paper
T 567 om-20 Determination of effective residual ink concentration (ERIC) by infrared reflectance measurement
Physical Properties
Pulp Properties
If no progress is made on balancing these SSIGs, then the respective methods may be considered for withdrawal at the next Q&SMC meeting. If you have an interest in becoming a member of either of these SSIGs please contact standards@tappi.org. or visit tappi.org/JoinStandards. Did You Know
... that to participate in the balloting process for TAPPI Standards you must sign up for the Standard-Specific Interest Groups (SSIGs)? Drafts are available for anyone... that to participate in the balloting process for TAPPI Standards you must sign up for the Standard-Specific Interest Groups (SSIGs)? Drafts are available for anyone to review, but to vote and comment you must be a member of the SSIG. Each Standard has its own SSIG – so you have to sign up for each Standard that you have an interest in. Links to all of the SSIGs (by subject category) can be found on the Subject Category for Standards web page. Visit tappi.org/JoinStandards to join now. Acronyms You May Need to Know
TIP = Technical Information Paper Q&SMC = Quality and Standards Management Committee SSIG = Standard-Specific Interest Group SARG = Standards Advisory Review Group WI = Work Item WG = Working Group WGC = Working Group Chair om = Official Method pm = Provisional Method sp = Standard Practice cm = Classical Method ss = Standard Specification sg = Standard Guideline gl = Standard Glossary wd = Withdrawn Standard UM = Useful Method Searching and Ordering TAPPI Standards, TIPs, and Useful Methods
Details on how to search and order TAPPI Standards, TIPs, and Useful Methods can be found on the TAPPI website’s Search and Order page. All individual TIPs or Standards are available for electronic or paper delivery. For electronic delivery, the documents are e-mailed in PDF format. Hard copy documents can be mailed or faxed, but shipping and handling costs will apply. For Individual TIPs, order Item Number: 0108____ (Insert TIP number) For Individual Standards, order Item Number: 0104T____ (Insert Standard number) For individual Useful Methods, order item number: 0104UM_____ (Insert UM number) List price: $49; TAPPI member price: $32. There are no shipping or handling charges for electronic documents. The TAPPI CD of Standards, TIPs, and UMs has been discontinued for 2021. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available. For information and quotes on company licenses, contact TAPPI Press (press@tappi.org) or +1-770-209-7277. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order on line at www.tappi.org. ------------------------------------------------------------------------------------------------------------------ Search and Order Individual Access or Company license Join a SSIG Develop a TIP Standards Guidelines TIPs Guidelines |
|
TAPPI Standards guidelines require that all TAPPI members receive notification of any proposed new Standards or TIPs. This message is being sent to you because of your affiliation with TAPPI; have purchased TIPs or Standards products from TAPPI; or because you have previously expressed interest in this topic.
TAPPI is the leading technical association for the worldwide pulp, paper and converting industry.
15 Technology Parkway South | Suite 115 | Peachtree Corners, GA 30092 | www.tappi.org
1-800-332-8686 (US) | 1-800-446-9431 (Canada) | +1-770-446-1400 (Worldwide)
TAPPI Privacy Policy
