| Archive | Subscribe | Printer-Friendly Version | Advertise | tappi.org | TAPPI Press Catalog | April 2024 |
New or Revised Standards, TIPs, and Useful Methods
Check here the list of TAPPI Technical Information Papers (TIPs) recently published: TIP 0402-11 Liquid penetrant testing of new suction roll shells (Revised) We extend our special appreciation to the following volunteers who served as Working Group Chairs in the recently published reviews of TAPPI TIPs: Michael Lykins - WGC for TIP 0402-11 Please note that the documents available for purchase on tappi.org and the Standards License Platform are updated monthly, usually around the 30th of each month. As a result, there may be a delay between the announcement of publication and their availability online. However, if you are subscribed to online access for Standards and TIPs and urgently require new documents that have not yet been posted, you can submit a request for TIPs to tip@tappi.org or Standards to standards@tappi.org. TAPPI Standards in Ballot
Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting. T 1014 om-15 Moisture sensitivity of fiber glass mats (April 25, 2024) The TAPPI Standards regulations require public review of standards that are up for ballot. Send a message to standards@tappi.org if you want to request a copy of the draft in ballot. If you would like to participate in the SSIGs that review and vote on the Standards, please contact TAPPI Standards Department at standards@tappi.org. General Announcements
Propose a New Standard or Technical Information Paper (TIP) Getting started is easy. Do you have just a general idea for a Standard, or are you farther along and have a substantial draft? If you just have a general idea for a Standard or TIP, complete the New Idea Submission form. TAPPI will review your idea and identify an appropriate committee or group to work on your suggestion. If you are further along, send an initial draft to standards@tappi.org. From there, the TAPPI Standards Manager will guide you through the appropriate process to finalize and approve the new document. STAR of the Month
This TIP describes a procedure for checking the parallel of corrugating rolls in a single facer using two-ply NCR paper. The impressions made on the paper by the corrugating roll flute tips are then compared to evaluate parallelism. Misaligned or out of parallel corrugator rolls can result in medium fracture, leaning flutes, and hi-lows. It can also reduce the “life” of corrugator rolls and the drive motor. The simplest method of checking the parallel of corrugator rolls is to use two ply NCR copy paper.
Parallel roll impressions. (Fig. 5) Date of Publication: February 29, 2024 Working Group Members: Tom Staal – Chair, Coastal Container If you would like to share your experience with Standards, TIPs or ISO TC 6, please write to standards@tappi.org and the TAPPI Standards team will be happy to interview you. Proposed New TIPs
The scope of the proposal for a new Technical Information Paper is shown below, as well as the assigned Subject Category, the date when the Work Item was opened, the title of the new proposal and the name of the Working Group Chair (WGC). 1101 - Process Control Scope: This document describes guidelines and recommended practices for the detection and quantification of dirt specks in a moving sheet of bleached kraft pulp using light transmitted through the pulp sheet. Dirt speck results are reported as “Physical” Size and not as the Equivalent Black Area (EBA) of the laboratory standard method T563, which must be measured with reflected light. If you would like to join the Working Group or review the final draft for this new proposal, please write to tip@tappi.org Members for Working Groups of TIPs needed
Volunteers for the following working groups of Technical Information Papers (TIPs) are needed. TIP 0402-38 Best practice guidelines for detecting and mitigating waterside cracking (stress-assisted corrosion) in power and recovery boilers TIP 0416-06 Keys to successful chemical cleaning of boilers TIP 0402-38 Best practice guidelines for detecting and mitigating waterside cracking (stress-assisted corrosion) in power and recovery boilers If you would like to join a Working Group of a TIP, please write to tip@tappi.org for more information. SSIG Members Needed
The Standard-Specific Interest Groups (SSIGs) for the following Standards are in need of additional members. These groups may or may not have ballots currently open. T 1212 sp-21 Light sources for evaluating papers including those containing fluorescent whitening agents Participating in a SSIG is free and open to anyone interested. Join now! If no progress is made on balancing these SSIGs, then the respective methods may be considered for withdrawal at the next Q&SMC meeting. If you have an interest in becoming a member of either of these SSIGs please contact standards@tappi.org Standards Coming Up For Review
The system for review and development of TAPPI Standards requires an announcement of review dates so that any interested TAPPI parties may access the drafts, submit comments, and/or join the Standard-Specific Interest Group (SSIG) to cast an official vote. Listed below are the Standards that will be up for review in 2024. The date indicated is the target date on which the draft will be distributed to the Standard-Specific Interest Group (SSIG) for that particular Standard. T 401 om-20 Fiber analysis of paper and paperboard (October 7, 2024) Any interested individuals who wish to be part of the voting for any Standard should send a message to standards@tappi.org and request voting membership on the corresponding SSIG, prior to the target ballot date, if possible. Anyone who joins the SSIG before the target balloting date will receive a notice of the ballot. Standards Ready for Final Approval at SARG
The list below shows Standards that are ready to be submitted to SARG at its Spring2024 meeting: *T 1008 sp-15 Test conditions for fiberglass mat test methods (Revision) A copy of the final draft for all these Standards can be found in the SARG page at https://www.tappi.org/Get-Involved/Develop-Standards-Methods/standards-advisory-review-group/ Announcement of SARG Meeting
The Standards Advisory Review Group (SARG) is a group of TAPPI members appointed by the Quality and Standards Management Committee (Q&SMC) who are familiar with the TAPPI Standards process and are qualified to participate in the final review of Standards after they have been approved by the appropriate Standards-Specific Interest Group (SSIG). SARG is required to meet twice a year to act on Standards that are in the final stage of review. The next meeting of the Standards Advisory Review Group (SARG) will be held virtually on Thursday, May 16th, 2024, 1:00 – 2:00 pm (EST). The SARG meeting is open to anyone for participation to discuss any appeals relevant to the Standards up for approval. The meeting agenda and links to the final drafts have been posted on the SARG Page. If you would like to participate virtually via Zoom, please email standards@tappi.org by May 9th, 2024 for access. Members for Working Groups of Useful Methods Needed
Reports outlining the overdue reviews for Standards and TIPs were sent to the Quality and Standards Management Committee (Q&SMC) on April 22, 2024. Copies of these reports were also sent to the assigned Working Group Chairs for these overdue reviews as well as to Chairs of the appropriate technical groups in TAPPI. Anyone who did not receive the overdue report but who have an interest may obtain a copy by requesting it from standards@tappi.org. Working Group Chairs: This report was sent to you for your information and action, if required. Q&SMC may, according to the Standards Guidelines, withdraw any Standards or TIPs whose reviews are overdue, especially if it appears that little progress is being made on the Work Item. If more information or indications of progress on these Work Items are received prior to the next meeting on May 16th, 2024, Q&SMC will take these reports of progress under consideration. To provide updates regarding this report, send a message to standards@tappi.org no later than May 9th, 2024, in order to provide this information to Q&SMC at their meeting. U.S. TAG to ISO TC 6
Next TC 6 Meeting(s) – Need to pre-register to attend. If you are a member of any working group (WG), please think about attending at least one of these meetings, or if you can’t please inform interim HOD of any important issues you may have. If you would like to know more or join the U.S. TAG to ISO TC 6, please write to isotc6@tappi.org. Did You Know
...that to participate in the balloting process for TAPPI Standards you must sign up for the Standard-Specific Interest Groups (SSIGs)? Drafts are available for anyone to review, but to vote you must be a member of the SSIG. Each Standard has its own SSIG – so you have to sign up for each Standard that you have an interest in. Links to all of the SSIGs (by subject category) can be found on the SSIG Join Page. When you click on a Subject Category, it will display links to related SSIGs. Acronyms You May Need to Know
For details on these commonly used acronyms in the development of TAPPI Standards and TIPs, please see the Standards Guidelines and the TIP Guidelines, or send your questions to standards@tappi.org. Searching and Ordering TAPPI Standards, TIPs, and Useful Methods
Details on how to search and order TAPPI Standards, TIPs, and Useful Methods can be found on the TAPPI website’s Search and Order page. All individual TIPs or Standards are available for electronic or paper delivery. For electronic delivery, the documents are e-mailed in PDF format. Hard copy documents can be mailed or faxed, but shipping and handling costs will apply. For Individual TIPs, order Item Number: 0108____ (Insert TIP number) List price: $53; TAPPI member price: $35. There are no shipping or handling charges for electronic documents. For information and quotes on company licenses, contact TAPPI Press (press@tappi.org) or +1-770-209-7277. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order online at www.tappi.org. Search and Order Individual Access or Company license Join a SSIG Develop a TIP Standards Guidelines TIPs Guidelines |
|
TAPPI Standards guidelines require that all TAPPI members receive notification of any proposed new Standards or TIPs. This message is being sent to you because of your affiliation with TAPPI; have purchased TIPs or Standards products from TAPPI; or because you have previously expressed interest in this topic.
TAPPI is the leading technical association for the worldwide pulp, paper and converting industry.
15 Technology Parkway South | Suite 115 | Peachtree Corners, GA 30092 | www.tappi.org
1-800-332-8686 (US) | 1-800-446-9431 (Canada) | +1-770-446-1400 (Worldwide)
TAPPI Privacy Policy
