STARTAPPINew or Revised Standards, TIPs, and Useful Methods
T 200 sp-15 "Laboratory beating of pulp (Valley beater method)" (Revision) T 213 om-15 "Dirt in pulp - chart method" (Revision) T 248 sp-15 "Laboratory beating of pulp (PFI mill method)" (Revision) T 259 om-15 "Species identification of nonwood plant fibers" (Revision and reclassification as an Official Method) T 401 om-15 "Fiber analysis of paper and paperboard" (Revision) T 409 sp-15 "Machine direction of paper and paperboard" (Revision) T 454 om-15 "Turpentine test for voids in glassine and greaseproof papers" (Revision) T 546 om-15 "Machine-direction grammage variation measurement (gravimetric method)" (Revision) T 555 om-15 "Roughness of paper and paperboard (print-surf method)" (Revision) T 558 om-15 "Surface wettability and absorbency of sheeted materials using an automated contact angle tester" (Revision) T 563 om-15 "Equivalent black area (EBA) and count of visible dirt in pulp, paper and paperboard by image analysis" (Revision) T 573 sp-15 "Accelerated temperature aging of printing and writing paper by dry oven exposure apparatus" (Revision) T 650 om-15 "Solids content of black liquor" (Revision) T 1007 sp-15 "Sample location for fiber glass mat sheets" (Revision) T 1008 sp-15 "Test conditions for fiberglass mat test methods" (Revision) T 1012 om-15 "Moisture content of fiber glass mats" (Revision) T 1015 sp-15 "Fiber glass mat uniformity (visual defects)" (Revision) TIP 0404-02 "Measurement of dryer condensing rates (batch method)" (Revision) TIP 0404-04 "Recommended tensions in dryer fabrics" (Revision) TIP 0404-20 "Physical characterization of press fabrics: basis weight, air permeability, void volume under loading and pressure uniformity" (Revision) TIP 0404-50 "Paper machine room ventilation guidelines" (Revision) TIP 0404-64 "Press fabric guiding" (Revision) TIP 0410-05 "Head of stock behind slice (head/jet relationships)" (Revision) UM 542 "Amount of coating on mineral-coated paper" (Revision) UM 554 "Polystyrene in paper products" (Revision) UM 555 "Testing of grease-repellant treated paper" (Revision)
TAPPI Standards in Ballot
The TAPPI Standards regulations require public review of standards that are up for ballot. Send a message to standards@tappi.org if you want to request a copy of draft in ballot. Listed below are TAPPI Standards that have recently gone out for ballot to the corresponding Standard-Specific Interest Group (SSIG). The date in parentheses is the closing date for voting. T 465 "Static creasing of paper for water vapor transmission tests" (June 8, 2015) T 566 "Bending resistance (stiffness) of paper (Taber-type tester in 0 to 10 Taber stiffness unit configuration)" (June 11, 2015) T 553 "Alkalinity of paper as calcium carbonate (alkaline reserve of paper)" (June 11, 2015) T 800 "Drum test for fiberboard shipping containers (revolving hexagonal drum)" (June 19, 2015) T 233 "Fiber length of pulp by classification" (June 19, 2015) General Announcements
T 840 om-10 "Testing adhesives used in glued lap joints of corrugated fiberboard containers" has been withdrawn. The reason for withdrawal is that a survey of the technical experts on the SSIG showed that most believed it would be better as a Useful Method. This method does not seem robust enough to be an Official Test Method, and there are many different evaluations wrapped into this test method. The way the method is written makes it challenging to understand how to proceed with repeatable testing in some cases, and the methods do not seem parallel. A new Useful Method replacing T 840 is in the works. Product & Product Quality Division committees are in need of new members to support the development and maintenance of standards we all use in the manufacture of the products we deliver to our customers. These committees discuss and make decisions on critical issues that deal with standards which are currently being used by the pulp and paper industry, as well as those which are being developed for them. Pulp and Chemical Properties Committee Tissue Properties Subcommittee Joining one or more of these groups gives you and your company the opportunity to participate in the discussion and development of the standards we use for evaluating the product and product quality. Without good pulp and paper industry standards to guide us, we will not be able to deliver what our customers require. Therefore, please consider volunteering your company and your support for these committees. For all those members who are already involved in Standard Specific Interest Groups (SSIG), we ask you to make the next step in standard development and maintenance participation by joining a committee today. Meetings are held twice a year to discuss ongoing committee work. The meetings can be attended in person or by phone conference. Getting started is easy. Do you have just a general idea for a standard, or are you farther along and have a substantial draft? If you just have a general idea for a standard or TIP, complete the New Idea Submission Form. TAPPI will review your idea and identify an appropriate committee or group to work on your suggestion. If you are further along, send an initial draft to standards@tappi.org. From there, the TAPPI Standards Manager will guide you through the appropriate process to finalize and approve the new document. Overdue Reports Distributed
A proposal has been made for a new Standard: "Specular Gloss at 20º -- Parallel Beam Method." This method is for the measurement of the specular gloss of high-gloss papers at 20° (70° from the plane of the paper). It is suitable for high-gloss coated, cast-coated, lacquered, highly varnished or waxed papers, and high-gloss ink films. A Standard-Specific Interest Group (SSIG) must be formed for this proposal. Any individuals who are interested in this Standard may join the SSIG to receive ballots when this method is ready for vote. If you would like to join the SSIG for this project, please notify the Standards Department at standards@tappi.org no later than June 15, 2015. SSIG Members Needed
The five-year review ballot for T 684 "Gross heating value of black liquor" was scheduled for May 12, 2015, but when the roster was pulled, there were only 8 members on the Standard-Specific Interest Group (SSIG). Ten is the minimum required by our regulations. If you would like to join this SSIG in order to help keep this standard active, please send a message to standards@tappi.org no later than June 15, 2015. Did You Know
. . . you do not have to be a TAPPI member to join any of the Standard-Specific Interest Groups (SSIGs)? To join an SSIG for a specific Standard, go to the Subject Categories page, where you will find links to sign up for as many SSIGs as you like. If you do not choose to join an SSIG, you can still request copies of any Standards up for ballot by sending a message to standards@tappi.org. After reviewing drafts, you may also send any comments to standards@tappi.org. The volunteer experts working on Standards are required to consider all comments received, but they are not required to accept comments from nonmembers of the SSIG. To ensure that your comments are addressed, then think about signing up for as many SSIGs as you like. Once you have signed up, you will be given instruction son how to log into the TAPPI balloting system. You will then be notified by email whenever one of the Standards you have signed up for is ready for voting. Acronyms You May Need to Know
For details on these commonly-used acronyms in the development of TAPPI Standards and TIPs, please see the Standards Guidelines and the TIP Guidelines, or send your questions to standards@tappi.org. TIP = Technical Information Paper Searching and Ordering TAPPI Standards, TIPs, and Useful Methods
Details on how to search and order TAPPI Standards, TIPs and Useful Methods can be found on the TAPPI website's Search and Order page. For Individual TIPs, order Item Number: 0108____ (Insert TIP number) For Individual Standards, order Item Number: 0104T____ (Insert Standard number) For individual Useful Methods, order Item Number 0104UM____ (insert UM number)
The 2015 collection of Standards, TIPs, and UMs, published in May of 2015 (product code STUCD-15), is available on CD. An Individual or Company License for access to the continually updated collection of Standards, TIPs, and UMs via the web is the best way to always have a current set of documents accessible. A print-on-demand version of either the Standards, TIPs, or UMs, current and updated as of the date printed, is also available. For information and quotes on company licenses, contact Ashley Westbrook (awestbrook@tappi.org) or +1-770-209-7228. For regular orders (including individual online licenses), contact Member Connection at 1-800-332-8686 (US), 1-800-446-9431 (Canada), or +1-770-446-1400 (international), or order on line at www.tappi.org. TAPPI Standards, TIPs and Useful Methods Online Subscription gives you point-and-click access, providing immediate answers anytime problems arise. You’ll save $186 alone by purchasing a subscription to Standards, TIPs and Useful Methods Online along with a TAPPI membership. This offer also applies each year you renew your membership. By joining TAPPI, you receive substantial savings on all TAPPI events, products and services and receive Paper 360, TAPPI Journal and Specialty Newsletters. Combine the Power of TAPPI Membership and the Quality of Performance by purchasing a TAPPI membership along with Standards online. Be a part of the TAPPI Community. TAPPI Membership $174 + Standards Online $125 = $299 TAPPI Standards, TIPs and Useful Methods – on demand – anytime, anywhere. |